IKO Flashing Replacement Nationwide

IKO Flashing Replacement: The San Diego Owner’s Guide

IKO flashing replacement in San Diego typically runs $280 – $640 installed, depending on the flashing location, length, and whether the surrounding shingles need to be lifted or replaced. We stock IKO-compatible flashing on our trucks and can usually complete a standard flashing swap the same day we diagnose it. Most homeowners discover the problem after a rainstorm: a water stain appears on the ceiling, peeling paint shows up near a wall junction, or they spot rusted metal curling away from a chimney or skylight while cleaning gutters.

Call (619) 810-5520

Flashing is the metal – usually galvanized steel, aluminum, or copper – that seals the seams where your roof meets something vertical: a chimney, a wall, a skylight, a vent pipe, or a valley where two roof slopes meet. IKO shingles are built to shed water, but flashing is what keeps that water from sneaking in at the joints. When it fails, the shingles can be in perfect shape and you’ll still get a leak.

Which IKO Models This Applies To

This applies across IKO’s residential shingle lines commonly installed in San Diego: the Cambridge, Dynasty, Nordic, and Royal Estate series, plus older Marathon and SuperEagle roofs that are still holding on in neighborhoods like Clairemont Mesa and Tierrasanta. The flashing itself isn’t made by IKO – it’s a separate metal component specified by the roofer at installation – but the way it integrates with IKO’s shingle profile matters. IKO shingles have a slightly different exposure and sealant strip position than GAF or CertainTeed, so the flashing step height and counterflashing overlap need to match IKO’s dimensions to shed water properly.

Here’s the compatibility gotcha we see often: if your original flashing was cut for a different shingle brand and then someone reroofed with IKO, the step flashing may be too short. It’ll look fine from the ground but leak at the first hard rain. A proper IKO flashing replacement means checking that each step flashing piece rises at least 4 inches up the wall and overlaps the shingle course below it by at least 2 inches. If you have the original roof installation paperwork, look for the flashing gauge – 26-gauge galvanized is the minimum we’ll install in coastal San Diego; anything lighter corrodes fast in salt air.

For homeowners deciding between OEM-branded flashing and quality aftermarket equivalents: IKO doesn’t manufacture its own flashing line. What matters is the metal gauge, the profile, and the installation, not a logo on the metal. We use 26-gauge or 24-gauge galvanized steel and aluminum flashing matched to San Diego’s coastal exposure, and we verify the profile against your specific IKO shingle course before cutting anything.

Key takeaways:

• IKO flashing replacement applies to Cambridge, Dynasty, Nordic, Royal Estate, Marathon, and SuperEagle roofs.
• Correct step flashing height for IKO profiles is 4 inches minimum up the wall, 2 inches minimum overlap.
• 26-gauge galvanized is the floor for San Diego coastal conditions.

Signs Your IKO Flashing Replacement Is Failing

• Water stains on ceilings or upper walls near a chimney, skylight, or wall junction. This is the most common first sign. The stain usually appears after sustained rain, not a light drizzle, because the flashing has to be overwhelmed before water travels far enough inward to show. By the time you see it on the ceiling, the flashing has been quietly failing for a while.
• Rusted or corroded metal visible along roof penetrations. If you can see rust blooms or orange streaking on the metal around a vent pipe or chimney from the ground, that’s galvanic corrosion doing its work. In San Diego’s salt-laden coastal air, 28-gauge flashing can rust through in 8-10 years. 26-gauge lasts longer, but nothing rustproof lives forever at the beach.
• Curling, lifting, or separated flashing pieces around skylights. Wind-driven rain gets behind flashing that has pulled away from the wall or skylight curb. You’ll see gaps at the top edge where caulk has dried and cracked. This is common on older skylight curb flashing in neighborhoods like Rancho Peñasquitos where original installs used exposed fasteners that have backed out.
• Granule loss and shingle damage concentrated around flashing edges. When flashing lifts, water gets under the shingle course below it, and that trapped moisture degrades the asphalt faster. If your roof looks fine except for a ring of damaged shingles around the chimney or a vent, the flashing is the culprit, not the shingles.
• Leaks that only happen when wind blows from one direction. Wind-driven rain from the east or southeast finds gaps that gravity-fed rain misses. If your leaks are inconsistent – only during certain storms – that often points to step flashing that’s too short or counterflashing that’s lost its seal.

Replacement Cost & What’s Included

Here’s what IKO flashing replacement costs in San Diego, installed:

• Pipe boot / vent pipe flashing: $280 – $380
• Chimney flashing (one side, step + counterflashing): $360 – $590
• Skylight curb flashing (per skylight): $420 – $740
• Valley flashing (per 10-foot run): $340 – $560
• Step flashing along a wall junction (per 10-foot run): $300 – $510

The range depends on access, roof pitch, whether we’re replacing a single piece or the full flashing system, and the condition of the shingles and underlayment underneath. A steep two-story roof in Mission Hills costs more than a single-story ranch in El Cajon because of ladder time and safety setup. Every price includes removal of the old flashing, new flashing matched to your IKO profile, replacement of any compromised underlayment, re-seating of surrounding shingles, and cleanup with a magnetic sweep. You’ll see a written price before any work starts – no number called from a truck and revised after the fact. That’s a flat rule at Mercer Roofing.

The work itself is covered by our 365-Day Done Right Promise: if it’s not right within a year, we make it right, and every flashing repair includes a written guarantee. A second visit to correct a failed repair is free.

DIY or Call Us?

There’s a narrow band of safe DIY inspection here, and then there’s everything else. From the ground or a safe ladder, you can check for visible rust, lifted metal, cracked caulk, and shingle damage around flashings. You can clear debris from valleys and around chimneys using a leaf blower or a soft brush. That’s where we’d draw the line.

Working on flashing means working on the roof edge, often at height, and it means lifting shingles that are nailed or sealed down. Getting flashing replacement wrong creates a leak that hides until the next big storm, and by then the decking underneath is soaked. We’ve also seen homeowners caulk over failed flashing, which holds for a few months and then lets go all at once. Flashing doesn’t get caulked back to life – it gets replaced. If you’ve spotted any of the failure signs above, call us at (619) 810-5520. We’ll come out, verify what’s actually failing, and give you a written price before any work starts. The estimate is free.

FAQs